View Categories

Procedure for Configuring Autologon User Automatic Login Using SecureAnyBox5 Agent



Principle of Operation #

The SecureAnyBox server changes the passwords of Autologon accounts as well. These accounts are used for automatic login on specified endpoints.

After every password change on the SecureAnyBox server, it is necessary to update the autologin account passwords on the affected endpoints so that the correct new password is used during the next restart or automatic login.

An Autologon account is a specially configured account in MS Windows that allows automatic login to the operating system immediately upon starting or restarting the device, without requiring the user to manually enter their username and password.

This approach is primarily used where the system needs to boot into a ready-to-use state without operator intervention. Examples of Autologon account usage include:

  • Kiosk (information or self-service terminals)
  • Shared computers (e.g., in hospitals)
  • ATMs
  • Computers available to guests in hotels or inmates in correctional facilities

Password changes for Active Directory accounts (if the Autologon user is a domain user) are handled by the LDAP agent, which is not installed separately but is part of the agent configuration on the SecureAnyBox server.

Password changes on target endpoints where Autologon accounts are used are managed by SecureAnyBox Agents.

The SecureAnyBox Agent runs on the endpoint as a system service and performs changes in the registry and system settings based on information received via a secured communication channel from the SecureAnyBox server.

This guide covers all the steps required to successfully set up, initiate, and operate password rotation for Autologon users (for both local and domain accounts).



Step 1: Create Agent Configuration #

Create an agent configuration containing settings for the MS Windows platform on workstation endpoints.

Depending on whether the Autologon user is local or domain-based, different settings need to be applied:

  • Local user on an MS Windows endpoint: In the agent configuration, select the MS Windows platform and, on the MS Windows tab, check the Update Autologon password checkbox.

    Agent configuration – Update Autologon password

  • Domain user: In the agent configuration, select the LDAP platform and, in the LDAP settings, set the Set password for field to autologon users.

    LDAP settings – Set password for autologon users



Step 2: Download Agent and Configuration #

On the Downloads page under the SecureAnyBox section in the user interface, download the SecureAnyBox5 agent for the MS Windows platform along with the agent configuration created in the previous step.

SecureAnyBox Downloads page



Step 3: Install Agent on Endpoint #

Install the SecureAnyBox5 agent on the MS Windows endpoint by running the installer. Once the installation is complete, import the agent configuration into the Windows Registry by double-clicking the secureanybox-agent.reg file.



Step 4: Configure Autologon User in Windows #

The Autologon user configuration can be performed using the autologon utility:

  • Download autologon utility from: https://secureanybox5.com/downloads/
  • Extract the downloaded ZIP archive on the target endpoint.
  • Open Command Prompt as Administrator.
  • In the command prompt, navigate to the folder where the autologon utility (autologon.exe) was extracted.
  • Run the utility and specify the Autologon user:

    • For a local user:

      • autologon.exe enable USERNAME PASSWORD

        Autologon command for a local user

    • For a domain user:

      • autologon.exe enable DOMAIN\USERNAME PASSWORD

        Autologon command for a domain user

  • If the autologon user setup is successful, the message Autologon enabled will be displayed.



Step 5: First Automatic Login and Password Rotation #

After restarting the endpoint (or restarting the SecureAnyBox agent service), the SecureAnyBox Agent communicates with the SecureAnyBox5 server and reports the configured autologon user to the server.

  • Autologon user is a local user:

    • The SecureAnyBox Agent changes the password for the local user in the registry.
  • Autologon user is a domain user:

    • The LDAP agent changes the password for the autologon user directly in LDAP. The changed password is then transmitted to the SecureAnyBox5 server. The SecureAnyBox agent retrieves the password during the next handshake with the server.

After restarting the endpoint, the autologon user should be logged in automatically.

If automatic login does not occur, check the SecureAnyBox user interface to verify that the autologon user is properly registered.

SecureAnyBox Endpoints – registered Autologon user

Additionally, you can use the SABMonitor tool (available in the SecureAnyBox5 server UI → SecureAnyBox → Downloads) to verify that the SecureAnyBox Agent is communicating with the SecureAnyBox5 server without issues.

SABMonitor – Agent communication status

If the autologon user password update is successful, SABMonitor displays default user password update complete.

If the autologon user is a domain user, you can run the LDAP agent and check the synchronization log to verify that the autologon user’s password was changed.

LDAP Agent synchronization log

Powered by BetterDocs